# Create VPC networks for exchange participant workloads

> [!NOTE]
> **GA with allowlist** : ULL Solution is available only to approved exchange operators and their exchange participants.
> If you are an approved exchange participant, contact [exchanges@google.com](mailto:exchanges@google.com) to request access.

This page describes how to do the following:

- Create Virtual Private Cloud (VPC) networks for exchange participant workloads, including Ultra Low Latency (ULL) VPC networks and general-purpose VPC networks.
- Add your ULL VPC network as a spoke to the Network Connectivity Center (NCC) hub created by the exchange operator. This establishes ULL unicast connectivity and lets you complete multicast configurations to establish ULL multicast connectivity.

For an overview of the ULL infrastructure configuration process, see
[Configuration overview for ULL Solution](https://docs.cloud.google.com/ull-solution/participants/configuration-overview.md.txt).

## Before you begin

Before you create VPC networks for ULL Solution,
see the following sections.

### Review VPC network requirements for ULL Solution

To complete the configuration process for ULL Solution, you
need each of the following VPC networks.

| Required VPC network | Supported instances and NICs | Description and network profile used |
|---|---|---|
| General-purpose VPC network | - U4C (`nic0`) - U4S | A network for general-purpose traffic, including management and service access. You can use either of the following: - A regular VPC network (no network profile) - A VPC network that is created with a regional network profile (regional VPC network), such as `us-south1-vpc-regional`. We recommend that you use a regional VPC network when configuring ULL Solution. |
| ULL VPC network | - U4C (`nic1`, `nic2`) | A network for ULL unicast and multicast traffic. To create this network, you use a zonal [participant ULL network profile](https://docs.cloud.google.com/ull-solution/participants/participant-ull-network-profile.md.txt), such as `us-south1-d-vpc-ull-participant`. |

### Review supported and unsupported features in ULL VPC networks

Make sure that you review the
[supported and unsupported features](https://docs.cloud.google.com/ull-solution/participants/participant-ull-network-profile.md.txt) in
participant ULL VPC networks. If you attempt to
configure unsupported features during network creation, Google Cloud
returns an error.

### Set your project

Set the gcloud CLI to use your project. Alternatively you can include
the `--project=PROJECT_ID` flag for each command
in the following procedures.

```
gcloud config set project PROJECT_ID
```

Replace `PROJECT_ID` with the ID of your
project.

### Enable APIs

If you haven't already, enable the following APIs.

### Console


Enable the Compute Engine and NCC APIs, if any are not already enabled.


**Roles required to enable APIs**


To enable APIs, you need the `serviceusage.services.enable` permission. If you
created the project, then you likely already have this permission through the
Owner role (`roles/owner`). Otherwise, you can get this permission through the
Service Usage Admin role (`roles/serviceusage.serviceUsageAdmin`).
[Learn how to grant roles](https://docs.cloud.google.com/iam/docs/granting-changing-revoking-access.md.txt).

[Enable the APIs](https://console.cloud.google.com/apis/enableflow?apiid=compute.googleapis.com,networkconnectivity.googleapis.com)

<br />

### gcloud


Enable the Compute Engine and NCC APIs, if any are not already enabled:


**Roles required to enable APIs**


To enable APIs, you need the `serviceusage.services.enable` permission. If you
created the project, then you likely already have this permission through the
Owner role (`roles/owner`). Otherwise, you can get this permission through the
Service Usage Admin role (`roles/serviceusage.serviceUsageAdmin`).
[Learn how to grant roles](https://docs.cloud.google.com/iam/docs/granting-changing-revoking-access.md.txt).

```bash
gcloud services enable compute.googleapis.com networkconnectivity.googleapis.com
```

<br />

### Required roles


To get the permissions that
you need to create participant ULL VPC networks,

ask your administrator to grant you the
following IAM roles:

- To create and manage network resources: Compute Network Admin (`compute.networkAdmin`) on your project
- To create NCC spokes: Spoke Admin (`networkconnectivity.spokeAdmin`) on your project
- To propose NCC spokes to the hub associated with a multicast domain: Group User (`networkconnectivity.groupUser`) on the multicast administrator project


For more information about granting roles, see [Manage access to projects, folders, and organizations](https://docs.cloud.google.com/iam/docs/granting-changing-revoking-access.md.txt).


You might also be able to get
the required permissions through [custom
roles](https://docs.cloud.google.com/iam/docs/creating-custom-roles) or other [predefined
roles](https://docs.cloud.google.com/iam/docs/roles-overview#predefined).

## Create a general-purpose VPC network

This section describes how to create a VPC network for
general-purpose traffic. You use this network for
the `nic0` interfaces of ULL Compute Engine instances, and for
creating non-ULL instances.

For more information about creating VPC networks, see
[Create and manage VPC networks](https://docs.cloud.google.com/vpc/docs/create-modify-vpc-networks.md.txt#create-custom-network).

### gcloud

1. Create a VPC network by using the
   [`compute networks create` command](https://docs.cloud.google.com/sdk/gcloud/reference/compute/networks/create.md.txt).

   ```
   gcloud compute networks create GENERAL_PURPOSE_NETWORK \
       --subnet-mode=custom \
       --network-profile=REGION-vpc-regional
   ```

   Replace the following values:
   - `GENERAL_PURPOSE_NETWORK`: a name for the general-purpose VPC network.
   - `REGION`: to create a regional VPC network by using a regional network profile, specify the region in which you are configuring ULL Solution, such as `us-south1`. You can alternatively remove the `--network-profile` flag to create a regular VPC network.
2. Add one or more subnets by using the
   [`compute networks subnets create` command](https://docs.cloud.google.com/sdk/gcloud/reference/compute/networks/subnets/create).

   ```
   gcloud compute networks subnets create GENERAL_PURPOSE_SUBNET \
       --network=GENERAL_PURPOSE_NETWORK \
       --range=PRIMARY_RANGE \
       --region=REGION
   ```

   Replace the following values:
   - `GENERAL_PURPOSE_SUBNET`: a name for the subnet.
   - `GENERAL_PURPOSE_NETWORK`: the name of the general-purpose VPC network that you created previously.
   - `PRIMARY_RANGE`: the primary IPv4 range for the subnet, in CIDR notation. For more information, see [IPv4 subnet
     ranges](https://docs.cloud.google.com/vpc/docs/subnets#manually_created_subnet_ip_ranges).
   - `REGION`: the region in which you are configuring ULL Solution, such as `us-south1`.
3. To connect to ULL compute instances by using SSH, the firewall rule
   configuration of the network for the `nic0` interface must allow SSH.

   To configure firewall rules for the general-purpose VPC
   network that you created, see the
   [Cloud Next Generation Firewall documentation](https://docs.cloud.google.com/firewall/docs/about-firewalls.md.txt).
   For regional VPC networks, we recommend that you use
   [regional network firewall policies](https://docs.cloud.google.com/firewall/docs/regional-firewall-policies.md.txt).

## Create a participant ULL VPC network

This section describes how to create a VPC network with the
participant ULL network profile for ULL unicast and multicast traffic.

### gcloud

1. Create a participant ULL VPC network by using the
   [`compute networks create` command](https://docs.cloud.google.com/sdk/gcloud/reference/compute/networks/create.md.txt)
   and specifying the appropriate zonal participant ULL network profile.

   ```
   gcloud compute networks create PARTICIPANT_ULL_NETWORK \
       --subnet-mode=custom \
       --network-profile=ZONE-vpc-ull-participant
   ```

   Replace the following values:
   - `PARTICIPANT_ULL_NETWORK`: a name for the participant ULL VPC network.
   - `ZONE`: the zone in which to create the network. The zone must be from the [list of supported locations](https://docs.cloud.google.com/ull-solution/participants/configuration-overview.md.txt#locations) for ULL Solution, such as `us-south1-d`.
2. Add at least two subnets to the network for attachments from ULL
   Compute Engine instances.
   For a given ULL instance, `nic1` attaches to one subnet in the network,
   while `nic2` attaches to another subnet in the same network.
   To add a subnet, use the
   [`compute networks subnets create` command](https://docs.cloud.google.com/sdk/gcloud/reference/compute/networks/subnets/create).

   ```
   gcloud compute networks subnets create ULL_SUBNET \
       --network=PARTICIPANT_ULL_NETWORK \
       --range=PRIMARY_RANGE \
       --region=REGION
   ```

   Replace the following values:
   - `ULL_SUBNET`: a name for the subnet.
   - `PARTICIPANT_ULL_NETWORK`: the name of the participant ULL VPC network that you created previously.
   - `PRIMARY_RANGE`: the primary IPv4 range for the subnet, in CIDR notation. For more information, see [IPv4 subnet
     ranges](https://docs.cloud.google.com/vpc/docs/subnets#manually_created_subnet_ip_ranges).
   - `REGION`: the Google Cloud region in which the new subnet is created. Must be the region that contains the zone in which you created the network, such as `us-south1`.

## Add the ULL VPC network to a NCC hub

This section describes how to add your ULL VPC network to the
NCC hub that was created by the exchange operator. To add your
network, you create a VPC spoke in the *edge* group.

Before proceeding, review the following:

- This step lets you establish ULL unicast connectivity with the exchange operator, and provides access to the ULL Multicast domains that are associated with a hub so that you can complete multicast consumer configurations to enable ULL multicast connectivity.
- You attach your ULL VPC networks to separate hubs created by the exchange operator for each zone. For example, one hub for ULL VPC networks in `us-south1-d` and one hub for ULL VPC networks in `us-south1-e`.
- You don't add your general-purpose VPC network to the same hub as your ULL VPC networks. However, you can add your general-purpose VPC network to a separate hub created by the exchange operator when you [configure Cloud Multicast](https://docs.cloud.google.com/vpc/docs/multicast/configuration-overview.md.txt).

For more information, see [Star topology](https://docs.cloud.google.com/network-connectivity/docs/network-connectivity-center/concepts/vpc-spokes-overview.md.txt#star-topology) and
[Create a VPC spoke](https://docs.cloud.google.com/network-connectivity/docs/network-connectivity-center/how-to/working-with-hubs-spokes.md.txt#create-vpc-spoke) in the NCC
documentation. If you use VPC Service Controls, see
[Cross-project VPC spoke proposals across service perimeters](https://docs.cloud.google.com/network-connectivity/docs/network-connectivity-center/how-to/vpc-use-vpcsc.md.txt#cross-project-spoke-proposals)
for the required ingress and egress rules.

### gcloud

1. To add your network as an edge spoke to a hub, use the
   [`network-connectivity spokes linked-vpc-network create` command](https://docs.cloud.google.com/sdk/gcloud/reference/network-connectivity/spokes/linked-vpc-network/create).

   ```
   gcloud network-connectivity spokes linked-vpc-network create SPOKE_NAME \
       --hub=projects/MULTICAST_ADMIN_PROJECT/locations/global/hubs/HUB_NAME \
       --vpc-network=PARTICIPANT_ULL_NETWORK \
       --group="edge" \
       --global \
       --include-export-ranges=INCLUDE_RANGES
   ```

   Replace the following values:
   - `SPOKE_NAME`: a name for the edge spoke
   - `MULTICAST_ADMIN_PROJECT`: the ID of the exchange operator project that is used to administer multicast
   - `HUB_NAME`: the name of the NCC hub that was
     created by the exchange operator. Your multicast consumer
     network must attach to the same hub as the exchange operator's *multicast
     administrator network* and *multicast producer network*. If
     necessary, contact the exchange operator for the name of the hub.

   - `PARTICIPANT_ULL_NETWORK`: the name of the participant
     ULL VPC network that you created previously

     You can alternatively provide the URI of the participant
     ULL VPC network by using the following format:
     `projects/PROJECT_ID/global/networks/PARTICIPANT_ULL_NETWORK`.
   - `INCLUDE_RANGES`: a comma-separated list of IP address
     ranges to export to the hub.

     By default, the spoke exports all subnet
     ranges. To avoid overlap with other spokes on the hub, you can specify
     which subnet ranges to export. If you specify subnet ranges, ensure that
     you include the ranges that host multicast consumers and any other
     ranges needed for communication with the spokes in the center group,
     such as for unicast traffic.

     Google Cloud prohibits subnet overlaps across VPC spokes
     as described in [Subnet route uniqueness](https://docs.cloud.google.com/network-connectivity/docs/network-connectivity-center/concepts/vpc-spoke-admin.md.txt#subnet-uniqueness). For more information about using export filters to avoid overlap, see [VPC connectivity with export filters](https://docs.cloud.google.com/network-connectivity/docs/network-connectivity-center/concepts/vpc-spokes-overview.md.txt#vpc-connectivity-with-export-filters).
2. Contact the exchange operator to notify them that you proposed
   a VPC spoke to the hub.

   If the hub is in a different project, then the exchange operator
   must explicitly approve your spoke before it becomes active, unless the exchange operator added your project as an auto-accept project.

   To check the status of a spoke after you create it, see [Check the status of a VPC spoke](https://docs.cloud.google.com/network-connectivity/docs/network-connectivity-center/how-to/vpc-check-spoke-status.md.txt).

## What's next

- [Create firewall policies for ULL VPC networks](https://docs.cloud.google.com/ull-solution/participants/firewall/create-firewall-rules.md.txt)