This page describes how to register, deregister, and re-register a
Citizens Broadband Radio Service Device (CBSD) by using single-step or multistep registration.

In single-step registration, a
[Certified Professional Installer (CPI)](https://docs.cloud.google.com/spectrum-access-system/docs/key-terms.md.txt#cpi)
provides all the device registration information to Spectrum Access System (SAS) from
the CBSD. The CBSD uses registration requests to
send all the required information.

Some CBSDs don't support single-step registration and must be registered
by using multistep registration. For registration
instructions specific to your CBSD, see your CBSD vendor
documentation.

## Before you begin

You can register only Federal Communications Commission (FCC)-approved CBSDs in
compliance with FCC Part 96 with SAS. Most
CBSDs require a CPI to verify the CBSD's
installation. For information about CBSD categories, see
[Register a CBSD that needs CPI validation](https://docs.cloud.google.com/spectrum-access-system/docs/cbsd/overview.md.txt#register-cbsd).

## Register your CBSD

Before a CBSD can transmit, it needs to register with
SAS. For more information, see
[Send a registration request to SAS](https://docs.cloud.google.com/spectrum-access-system/docs/portal.md.txt#sending-cbsd-registration).

If your registration request is successful, SAS responds with
a CBSD ID. The CBSD is then registered.
If your registration request is rejected, SAS responds with
an error message. The CBSD needs to correct the error and send
another registration request. For more information, see
[Register a CBSD that needs CPI validation](https://docs.cloud.google.com/spectrum-access-system/docs/portal.md.txt#register-cbsd).

To register your CBSD, follow these steps:

1. In the CBSDs list or CBSD details, click **CBSD Actions** , and then click **Register**.
2. Check if your CBSD registered successfully.
3. Make sure that your CBSD appears in the CBSD list.

> [!IMPORTANT]
> **Important:** If you select **Grant** , it performs the **Register** action. If that succeeds, then it performs the **Grant** action.

## Deregister your CBSD

If a CBSD needs to be decommissioned or moved, the CBSD should first
send a deregistration request to SAS. This indicates that the
CBSD no longer wants to be listed in SAS with
the parameters that it originally had. Contact your device vendor for
documentation or instructions to deregister your CBSD. If a
CBSD needs to transmit again, the CBSD can send a
registration request with updated parameters.

The Google SAS Portal gives you a way to deregister your
CBSD in the situation that a CBSD is no longer
able to send a deregistration request. You can deregister a device by using the
SAS Portal device panel or
**Table view**.

To deregister the device by using the SAS Portal device panel, follow
these steps:

1. Go to the [SAS Portal](https://wirelessconnectivity.google.com/sas).
2. Select the CBSD from the **Deployments** list.
3. Select **Table view** or **Map view** , and then click **Device panel**.
4. On the right, click **Device** , and then click **Deregister CBSD**.

To deregister the device by using **Table view**,
follow these steps:

1. Go to the [SAS Portal](https://wirelessconnectivity.google.com/sas).
2. Select the CBSD from the **Deployments** list.
3. Click **Table view**.
4. Right-click the row of the CBSD that you want to deregister.
5. Select **Deregister CBSD**.

## Re-register your CBSD

If you are a CPI, you can update the SAS configuration by creating an
inactive configuration. You need to sign the inactive configuration and instruct
the CBSD to send a new registration request to
SAS. The CBSD loses all current grants.

To re-register a CBSD, follow these steps:

1. Go to the [SAS Portal](https://wirelessconnectivity.google.com/sas).
2. Click **View deployments**.
3. Optional: If you have access to multiple deployments, select a deployment from the **Deployments** list, and then click **Open**.
4. On the left, click **Settings**.
5. To select the CBSD, do the following:
   - In **Map view**, click the CBSD location marker.
   - In **Table view**, click the row of the CBSD.
6. Click **Edit**.
7. Update and review the CBSD configuration, and then do the following:
   - If you are an Editor, click **Ready for CPI**.
   - If you are a CPI, click **Sign**.

After re-registering, the inactive configuration status changes to
**Pending registration** . However, if the CBSD was already registered,
the CBSD status doesn't change while the SAS is
still using the previous (active) configuration. You can find the changed
configuration in the **Pending changes** section.

When the CBSD re-registers with SAS, the inactive
configuration becomes the active configuration. The **Pending changes** section
disappears, and the CBSD information page updates with the new set
of parameters used in the most recent registration.

## Register a CBSD by using vendor-specific registration parameters

You can register a CBSD directly from your device, but if you use
a vendor (Baicells or Telrad) device, then you must add vendor-specific
registration parameters to the device. For details, see the following sections.

### Baicells registration parameters

Use these instructions if you have a vendor device such as Baicells. To
successfully configure your CBSD and upload the CPI certificate,
make sure that you fill in the necessary fields in Baicells. All
CBSD configurations are performed in the Baicells device user interface (UI) or
by using the Baicells Operations Management Console (OMC).

> [!IMPORTANT]
> **Important:** This process can vary by vendor. For additional help, contact your vendor.

#### Configure installation parameters directly in the CBSD UI

The CPI certificate is uploaded directly to the CBSD, which signs
and encodes all installation parameters. The encoded CPI data is sent to the OMC
and Domain Proxy (DP) service, which is then passed to SAS during the
registration request. You don't need to add the CBSD in the
SAS Portal. SAS settings are configured as
follows:

- For the CBSD UI, set **SAS Registration Type** to **Single-Step**.
- For the OMC and DP service, select **Single-Step**, and then upload the CPI certificate.

#### Configure installation parameters by using the OMC and DP service

You can enter the installation parameters by using the OMC and DP service, and then the CPI signs
them. You don't need to add the CBSD in the SAS
Portal. SAS settings are configured as follows:

- For the CBSD UI, set **SAS Registration Type** to **Single-Step**.
- For the OMC and DP service, select **Single-Step**, and then upload CPI certificate.

### Telrad registration parameters

To configure installation parameters for the Telrad device, follow these steps:

1. In **BreezeVIEW**, go to the CBSD list page.
2. Click **Add CBSD**.
3. Set the CBSD Device Type:
   - For **eNB**, enter the Device ID and Cell ID (0, 1).
   - For **UE**, enter the IMSI ID.
4. Add UE CBSD.
5. Add a new CBSD.
6. Use the BreezeVIEW CLI to sign the CPI.
7. Configure the CBSD. After the new CBSD is added, the details page appears.
8. Set the CBSD parameters, and then click **Save**.

## What's next

- [Use deployments to organize CBSDs](https://docs.cloud.google.com/spectrum-access-system/docs/cbsd/organize.md.txt)
- [Manage CBSD configurations](https://docs.cloud.google.com/spectrum-access-system/docs/cbsd/manage-configurations.md.txt)