This page describes how to set up a Citizens Broadband Radio Service Device (CBSD) configuration.

Before a new CBSD starts transmitting, it needs to
register with Spectrum Access System (SAS) and send information about its
physical installation such as the radio model, location, and antenna parameters.

## Registration prerequisites

Some CBSDs only support multistep registration and therefore
must be pre-configured in the Google SAS Portal or by using the
Google SAS Portal API.

Single-step registration is when a
[Certified Professional Installer (CPI)](https://docs.cloud.google.com/spectrum-access-system/docs/key-terms.md.txt#cpi)
provides device registration information to SAS in the
registration request from the CBSD. For registration instructions that are
specific to your CBSD, see your CBSD vendor documentation.

Only [Federal Communications Commission (FCC)](https://docs.cloud.google.com/spectrum-access-system/docs/key-terms.md.txt#fcc)-approved
CBSDs in compliance with FCC Part 96 can be
registered with SAS. Most Category A and all Category B
CBSDs require a CPI to verify the device's installation.

Category A CBSDs that meet at least one of the following
conditions require a CPI validation:

- The CBSD does not automatically determine its location.
- The CBSD operates outdoors with an antenna height above average terrain (HAAT) of more than six meters. This type of CBSD must be registered as a Category B device.

## Use multistep registration

The following sections describe how to use multistep registration to register a CBSD.

### Configure installation parameters

To configure the installation parameters, follow these steps:

1. Create a [CBSD configuration](https://docs.cloud.google.com/spectrum-access-system/docs/portal.md.txt#cbsd-config) by using the SAS Portal or the SAS Portal API.
2. Import a CBSD by using the SAS Portal to create, sign, and update multiple CBSD configurations. For more information, see [Import the CBSD configuration](https://docs.cloud.google.com/spectrum-access-system/docs/cbsd/manage-configurations.md.txt).
3. Configure the installation parameters:
   - **Editors or admins only**: On the right, enter the installation parameters.
   - **CPIs** : Click **Sign device directly** or, to save as a draft, click **Save**.

> [!NOTE]
> **Note:** To configure parameters, you can use either the **Map view** or **Table view** . For more information, see [Register a CBSD that needs CPI validation](https://docs.cloud.google.com/spectrum-access-system/docs/portal.md.txt#register-cbsd).

### Sign the installation parameters

To sign off on the installation parameters, you must be a CPI and have
[verified your CPI identity in the SAS Portal](https://docs.cloud.google.com/spectrum-access-system/docs/validate-cpi-certification.md.txt).
To get CPI privileges, contact your administrator.

### Register the CBSD to SAS

The steps to connect a CBSD with SAS might be
different for each CBSD model. Check with your device vendor for
documentation or instructions. Google SAS combines the
information from the Google SAS Portal to process the
registration request from the CBSD. If the registration request
is successful, SAS responds with a CBSD ID. The
CBSD is registered and can now request a grant.

If SAS rejects the registration request, it responds with an
error message. The CBSD needs to correct the error and send
another registration request.

> [!TIP]
> **Tip:** For additional help, watch our [Getting Started videos on YouTube](https://www.youtube.com/watch?v=ly3H9_28COU).

The SAS portal rejects registration requests for any
CBSD configurations that are already signed. You must enter CBSD
parameters into the SAS Portal including the user ID, FCC ID,
and the serial number.

## Register your CBSD

You can register your CBSD by using the Google SAS Portal
or, if you are using Baicells equipment, by using Baicells.

### Use the SAS Portal

If you are using the SAS Portal to configure installation parameters, follow these steps:

1. Enter the installation parameters for a CBSD configuration.
2. Optional: If you aren't a CPI, click **Save** to save the draft of the CBSD configuration.
3. Click **Ready for CPI** to indicate that you're finished with the configuration.
4. After the CBSD configuration is signed by the CPI, a registration request can be sent from the device to Google SAS.
5. If the registration request is successful, the CBSD is registered.

### Use Baicells

If you are using Baicells equipment to configure installation parameters, follow these steps:

1. Configure the CBSD in Baicells.
2. Export the CBSD configuration from Baicells as a CSV file.
3. To complete Step 1, configure the installation parameters and import this CSV file into the Google SAS Portal.
4. To complete Step 2 of the multistep registration, go back to Baicells, select the CBSD, and then send the registration request.

## What's next

- Learn about [Spectrum Access System](https://docs.cloud.google.com/spectrum-access-system/docs/overview.md.txt).
- Learn about [key SAS terms](https://docs.cloud.google.com/spectrum-access-system/docs/key-terms.md.txt).
- [Troubleshoot SAS issues](https://docs.cloud.google.com/spectrum-access-system/docs/troubleshooting.md.txt).